© DenLorsTools.com Summary: Applies to 2002 to 2009 second generation Trailblazers and Envoys with 4.2 Liter in-line 6 cylinders. This auto repair article is for GMC Envoys or Chevrolet Trailblazers when a P1281 fault code is scanned using a code reader or scan tool. The P1281 fault code is related to the engine not reaching operating temperature within the set parameter. More explanation of what the code means and suggestions on how to complete the repair much easier. Using any code reader or scan tool with OBD II capability is all that is needed to read and erase the fault code.

The thermostat is NOT just to keep the engine cool, it also helps the engine heat up quickly to normal operating temperature within a certain time-frame. For the catalytic converter to operate at it’s highest efficiency the computer needs to be in closed loop. Closed loop means that the computer is in more control of fuel mixtures based on inputs from several sensors. Until the engine is running at the normal operating temperature, the computer usually controls the fuel mix less efficiently. That’s why it’s important for the thermostat to stay closed until the engine warms up quickly. If it stays open or opens up too quickly the motor will not reach the desired temp as quickly as it should. Most of the time when this code is retrieved, the t-stat is not working properly.

1/4″ swivel socket and extension pictured above used to start the bolts.

The thermostat is located on the left side of the engine. After removing the driver’s front wheel the t-stat housing can be seen over the frame. A long 1/4″ extension and 10mm swivel socket makes accessing the bolts holding the housing much easier. Usually this thermostat comes with a new housing as well. The tricky part is starting the bolts back in when installing the new t-stat. It’s easy to drop the bolts before actually getting them started. An old trick for holding bolts in place in hard to get to areas is to use small orings to act as a retainer. The o-rings are perfect for preventing the bolts from falling and are small enough to be collapsed when the bolts are tightened as to not cause any problems with the housing seating properly.

To help hold the bolts in place small o-rings are used to prevent them from falling.

Once the thermostat is replaced and the coolant is refilled, the fault code can be cleared. Usually it’s best to run the heater when topping off the coolant to help remove any air pockets that may be in the cooling system. When the heat is blowing hot and the temperature is in the normal range the coolant level will be full. Hopefully this repair article has helped explain and answer questions about the P1281 fault code scanned with a code reader or scan tool. Be sure to check out the links below for even more information and specialty tools.

Related Car Repair Blogs and Auto Tools

Jeep Grand Cherokee Scanned P1281 Fault Code / DenLors Auto Blog 

OBD II Scan Tools and Code Readers – DenLors Tools

Lisle Coolant Funnel to Remove Trapped Air in Cooling System

P0017 Chevy Trailblazer, Envoy, GMC Canyon, Colorado – Fault Codes

Chevy Auto Repair Articles – Automotive Repair Blogs for Chevrolet

Car Mechanics Specialty Tools – Automotive Tools and Shop Supplies

Mode $06 misfire information displayed

Misfires particularly in Ford cars and trucks can many times be identified before a misfire code sets and turns the CEL (Check Engine Light) on. This is a huge time saver, especially when there is a definite misfire felt but the code seems to take forever to appear. Fords take a long time in some cases to run through it’s necessary drive cycles needed for self testing. Auto technicians deal with this common problem of diagnosing misfires on Ford vehicles with no codes set by using Mode $06. Usually only manufacturer specific scan tools will display misfire data when there’s no code, but OBD 2 generic scan tools that can access mode 6 on Ford vehicles can be a great help.

Read the rest…

Jump straight to the best deal on an OTC Genisys EVO right now – OTC3869 Fall 2011. DenLors has many automotive tools for sale and we answer many questions everyday. The questions below were asked recently related to Genisys scan tools and I thought I would share my responses, in case it may help others when considering the purchase of a Genisys scan tool, accessories or European software updates. Keep in mind information on software and limited time deals are obviously time sensitive, so consider the date of this post. You may also be interested in a previous post – OTC

Genisys Still Hard to Beat. Read the rest…

It seems that with all the new choices for wireless automotive scan tools now, information is hard to come by. Our recently revised automotive tech article compares the top three wireless, touch screen automotive scan tools from Snap On (Verus), OTC (Pegisys) and Launch (X431Tool). Snap On known for it’s quality tools and yes, high prices.

Read the rest…

Good – Simple Actron Code Reader CP9125

The CP9125 Actron code reader is a very popular choice for the DIY (Do it Yourself-er) and for many used car dealers that want to read codes before the auction (or clear the codes prior to their car being ran through). The size of this tool makes it easy to carry in your pocket. No frills, just a good basic code reader with about 3,000Â definitions for Global OBD 2 codes.

Read the rest…